cone Calculator

Always good to have some helpful tips when making stove.
Where to get materials cheap, what tool is best.
How to do a specific task. Anything that will help.
User avatar
zelph
Posts: 15834
Joined: Tue Aug 14, 2007 1:53 pm

Re: cone Calculator

Post by zelph » Sun Feb 17, 2008 7:37 pm

Daren, very nicely done, easy to understand. Great photos and easy to se points to swing arc.

I like the miniture bungy cords used to hold the trammel point secure :)

I'm sure the instructions and photos will be helpfull. Thank You!!!
http://www.woodgaz-stove.com/

User avatar
DarenN
Posts: 2816
Joined: Wed Feb 06, 2008 11:46 am
Location: Surrey, B.C. Canada

Re: cone Calculator

Post by DarenN » Sun Feb 17, 2008 8:39 pm

;) bungie and velcro! how did the human race survive without them! :lol:

tip:: bungie makes a great tie-down for tarps in windy areas. at a kayakers gathering we once joked about getting all the tarps "set" to get the best possible speed out of the island we were camped on. :roll:
"I'd rather be happy than right." Slartibartfast

User avatar
zelph
Posts: 15834
Joined: Tue Aug 14, 2007 1:53 pm

Re: cone Calculator

Post by zelph » Mon Feb 18, 2008 2:08 pm

DarenN wrote:;) bungie and velcro! how did the human race survive without them! :lol:

tip:: bungie makes a great tie-down for tarps in windy areas. at a kayakers gathering we once joked about getting all the tarps "set" to get the best possible speed out of the island we were camped on. :roll:
For a long time the world was strickly duct tape :mrgreen:

Must be small "Bog" islands. Hard to tell that their floaters :mrgreen:
http://www.woodgaz-stove.com/

User avatar
dlarson
Site Admin
Posts: 429
Joined: Tue Jul 08, 2008 10:02 pm
Location: minnesota

Re: cone Calculator

Post by dlarson » Sat Aug 02, 2008 6:32 pm

Darren, nice tutorial!
I was wondering, what's the tolerance when stepping along an arc in 1 inch increments? Wouldn't the distance measured along the arc gradually get too long as one continues stepping along it?
"Hiking is just walking where it's O.K. to pee." -Demetri Martin

User avatar
DarenN
Posts: 2816
Joined: Wed Feb 06, 2008 11:46 am
Location: Surrey, B.C. Canada

Re: cone Calculator

Post by DarenN » Sat Feb 06, 2010 2:37 pm

dlarson wrote:Darren, nice tutorial!
I was wondering, what's the tolerance when stepping along an arc in 1 inch increments? Wouldn't the distance measured along the arc gradually get too long as one continues stepping along it?
using 1" increments the lengthenning you mention is too minimal to worry about. if we were building watches it might make a difference, but i doubt it.

Daren.......
"I'd rather be happy than right." Slartibartfast

User avatar
zelph
Posts: 15834
Joined: Tue Aug 14, 2007 1:53 pm

Re: cone Calculator

Post by zelph » Sat Feb 06, 2010 10:30 pm




http://www.outdoorsmagic.com/forum/foru ... /v/100/sp/


Looks like something Mags threw out and someone picked it up and recycled it.

http://www.whiteblaze.net/forum/vbg/sho ... offdate=14
http://www.woodgaz-stove.com/

Post Reply